Polycap TF

Polycap™ TF filter devices are among the finest disposable encapsulated filters. These capsules are made with durable, hydrophobic polytetrafluoroethylene (PTFE) membranes in a polypropylene housing and are designed for use with organic solvents and chemically aggressive solutions.

Features and benefits

Resistant to most solvents, autoclavable and integrity-testable
Available in 0.05, 0.1, 0.2, 0.45 and 1.0 µm pore sizes
0.05 µm capsules designed for ultra-clean applications; 1.0 µm used for extended life and filtration of highly contaminated solutions
Able to be sterilized by autoclaving with steam or EtO
Manufactured under very clean conditions in a Class 10 000 clean room and under ISO Quality Systems

Applications

Venting
In-line filtration
Isolation
Electronics
Pharmaceutical
Biotech
Laboratory
Other uses

Technical Properties - Polycap TF
Housing	Polypropylene
Membrane	PTFE
Vent	On inlet
Support system	Polypropylene
Sealing	Heat-fused
Maximum pressure	4.1 bar (60 psi)
Flow direction	Supported bidirectionally. Certain applications may require orientation, i.e., vents. Reverse flow only for low pressure applications.
Biosafety	Materials pass USP Class VI
Sterilization	May be autoclaved at 121°C for 20 minutes (maximum 132°C). Multiple autoclave cycles are possible. However, the responsibility for reuse is with the operator. The device should be protected from cross contamination. An integrity test should be performed after autoclaving. Compatible with EtO sterilization
Filtration area	36 mm capsule: 500 cm² (77 in²) 75 mm capsule: 1000 cm² (155 in²) 150 mm capsule: 2000 cm² (310 in²)
IPA bubble point	0.05 µm membrane: > 2.4 bar (35 psi) 0.1 µm membrane: > 1.7 bar (25 psi) 0.2 µm membrane: > 0.9 bar (13 psi) 0.45 µm membrane: > 0.5 bar (7 psi) 1.0 µm membrane: > 0.2 bar (3 psi)
SB - Stepped barb for 6 to 10 mm (1/4 to 3/8") tubing 1/2 SB - Stepped barb for 10 to 12 mm (3/8 to 1/2") tubing MNPT - Male national pipe thread FNPT - Female national pipe thread HB - Hose barb

Ordering Information - Polycap TF
Catalog Number	Description
6711-3601	Polycap TF 36, 0.1 µm, with MNPT inlet and SB outlet, 1/pk
6711-3602	Polycap TF 36, 0.2 µm, with MNPT inlet and SB outlet, 1/pk
6710-3602	Polycap TF 36, 0.2 µm, with 1/2 SB inlet and outlet, 1/pk
6700-3602	Polycap TF 36, 0.2 µm, with SB inlet and outlet, 1/pk
2601	Polycap TF 36, 0.2 µm, with SB inlet and outlet, 5/pk
2601T	Polycap TF 36, 0.2 µm, with FNPT inlet and outlet, 5/pk
6711-3604	Polycap TF 36, 0.45 µm, with MNPT inlet and SB outlet, 1/pk
2602S	Polycap TF 36, 0.45 µm, with 1 1/2" Sanitary inlet and outlet, 5/pk
6700-3610	Polycap TF 36, 1.0 µm, with SB inlet and outlet, 1/pk
2603	Polycap TF 36, 1.0 µm, with SB inlet and outlet, 5/pk
2603T	Polycap TF 36, 1.0 µm, with FNPT inlet and outlet, 5/pk
6700-7501	Polycap TF 75, 0.1 µm, with SB inlet and outlet, 1/pk
2700T	Polycap TF 75, 0.1 µm, with FNPT inlet and outlet, 5/pk
6711-7502	Polycap TF 75, 0.2 µm, with MNPT inlet and SB outlet, 1/pk
6710-7502	Polycap TF 75, 0.2 µm, with 1/2 SB inlet and outlet, 1/pk
6700-7502	Polycap TF 75, 0.2 µm, with SB inlet and outlet, 1/pk
2702M	Polycap TF 75, 0.2 µm, with MNPT inlet and outlet, 5/pk
2702T	Polycap TF 75, 0.2 µm, with FNPT inlet and outlet, 5/pk
6700-7504	Polycap TF 75, 0.45 µm, with SB inlet and outlet, 1/pk
2703T	Polycap TF 75, 0.45 µm, with FNPT inlet and outlet, 5/pk
6701-7510	Polycap TF 75, 1.0 µm, with 1/2 SB inlet and outelt, 1/pk
2704T	Polycap TF 75, 1.0 µm, with FNPT inlet and outlet, 5/pk
2800T	Polycap TF 150, 0.1 µm, with FNPT inlet and outlet, 5/pk
2802T	Polycap TF 150, 0.2 µm, with FNPT inlet and outlet, 5/pk
2801	Polycap TF 150, 0.2 µm, with 1 1/2" Sanitary inlet and outlet, 5/pk
2803T	Polycap TF 150, 0.45 µm, with FNPT inlet and outlet, 5/pk
2804T	Polycap TF 150, 1.0 µm, with FNPT inlet and outlet, 5/pk